AC200Max

Watch the video: BLUETTI AC200MAX | Menu&Settings

1. AC200MAX is only compatible with B230 or B300
2. No, AC200MAX connects to B230 or B300 using P090D, which is included in the box of B230/B300.

1. AC200MAX supports up to 2 B230s, with a capacity of up to 6144Wh.
2. AC200MAX supports up to 2 B300s, with a capacity of up to 8192Wh.
3. B230 batteries and B300 batteries can be mixed and connected to AC200MAX, and up to 2 battery packs can be connected when mixed.

AC200MAX does not have UPS function.

Yes. Can only be connected to the Bluetti App via Bluetooth.

You can use the AC200MAX to charge your devices in cold weather, but please avoid recharging it below freezing. The operating temperature for AC200MAX is:
Charging: 0℃~40℃ / 32℉~104℉
Discharging: -20~40℃ / -4~104℉

The main differences are as follows:
1. Battery capacity: AC200MAX has a capacity of 2048Wh and supports expansion with 2 B230/B300, with a maximum capacity of up to 8192WhWh, while AC200P has a capacity of 2000Wh and does not support expansion. The battery pack can only charge AC200P in power bank mode.
2. Maximum output power: AC200P's AC output power is 2000W; while AC200MAX's AC output power is 2200W, and the maximum output power of DC output ports such as USB-C port, RV port, and DC5521 port is also higher than AC200P.
3. AC output port: AC200MAX has a TT-30 output port, while AC200P only has a 20A output port.
4. Maximum charging power:; AC200P's PV charging power is 700W, while AC200MAX's PV charging power is 900W, and the PV input range is also wider than AC200P.
5. APP Bluetooth function: AC200MAX supports, but AC200P does not support.

Charging time (estimated) = (Capacity/Charging power) + Trickle charging time.
Trickle charging time for Bluetti power station is typically 0.5~1 hours.

Adapter maximum charging power 500W.
PV maximum charging power 900W.
Adapter + PV maximum charging power 1400W.

AC200MAX Each channel can connect 1~5 PV120, 1-5 PV200, 1~3 PV350, 1~3 PV420.

It is best to connect all solar panels in series, because the AC200MAX PV input has a wide voltage range of 12V~145V, and the maximum input current is only 15A. The series voltage increases, and the parallel current increases, so the series efficiency is higher. Be careful not to mix and connect different types of solar panels, otherwise it will affect the efficiency and damage the solar panels over time.

The solar input current can exceed 15A. Our machine will limit the current, but exceeding it is equivalent to waste. The current can exceed, but the voltage cannot exceed.

Solar input power can exceed 900 watts, as long as the total PV VOC of each circuit does not exceed 145V.

Yes, as long as the solar panel specifications are within the following range:
1. Total VOC: 12V~145V
2. Total power: Maximum 900W
3. With MC4 connector

Yes, as soon as your solar roof meet the following conditions:
1. Total VOC 12V~145V
2. With MC4 connectors
3. The AC200MAX can be charged by microinverter ONLY through an AC outlet rather than directly charging.

No

1. The output specifications, voltage and frequency of the generator need to be within the input range of the adapter.
2. The maximum output power of the generator must be greater than the maximum charging power of the adapter. If this is not the case, the generator may be overloaded and unable to support charging our machine.
3. The output of the generator is a sine wave.

Yes, you can connect the battery pack to PV or adapter to charge the whole system, but AC200MAX will not display the charging power of the battery pack connected alone.

Yes, long press the battery pack power button for 5~10 seconds until the power button flashes, and the battery pack power bank mode is turned on. Watch the Video

Supports AC+DC dual charging, but DC has only one input port, so it only supports AC+solar panel charging or AC+car charging at the same time. If equipped with D050S, it supports two DC charging for AC200MAX.

No

Standard
AC200MAX
1. AC adapter-L=1500mm (low voltage, British standard), L=1800mm (European, Australian standard)
2. PV charging cable-L=500mm
3. Car charging cable-L=500mm
4. DC input cable-L=1000mm
B230
1. AC adapter-L=1500mm (low voltage, British standard), L=1500mm (European, Australian standard)
2. P090D-L=800mm
Others
Lead-acid battery charging clip L=500±15mm
12V/30A RV cable L=1500+500mm±30mm
Cigarette lighter to DC5521 cable (12V)-L=720mm
DC7909 to XT90 cable-L=50mm

No, please put it in a dry place. The working humidity range of AC200MAX is 10%~90%.

1. When the SOC drops to 5%, charge the product immediately.
2. Before storing the product, charge it to 60% SOC to maintain optimal condition. In addition, power off the device and disconnect all electrical connections.
3. Store the product in a cool, dry place, away from flammable or combustible materials and gases.
4. The power station can be safely stored in a temperature range of -20°C to 45°C (-4°F to 113°F).
113°F). However, if stored for more than one month, it is recommended to keep the ideal storage temperature around 30°C (86°F).
5. Fully cycle the product every 3 months to maintain the health of the battery.

Not recommended, as long-term placement may cause the internal structure to loosen. It is recommended to place it upright.

No

No, the maximum output voltage of T200S is 25.2V, which cannot meet the adapter input voltage requirement of AC200MAX. You have to use T500 to charge AC200MAX.

Yes. However, the max charging power would be limited to 100W / 200W. And please setup the "DC input source" to "Others".

1. If the lead-acid battery is equipped with an AC-DC adapter, the battery can be charged from the machine's AC output port.
2. If the battery is charged directly from the machine's DC output port, it is not supported.

Power saving mode: when this function is turned on, if the AC or DC of the machine has no load or the load power is too small, the machine will automatically turn off the AC or DC after 4 hours to reduce the machine's self-consumption and save power.

No, the AC200MAX's maximum AC output power is 2200W, and when outputting 120V, it can only output about 18.3A at most. The TT-30 socket supports a maximum of 30A, but it does not mean that the machine will output 30A. The TT-30 output port is mainly to provide customers with more socket options, only in the United States.

Yes, as long as the total load power does not exceed the maximum output power of the machine.

No

You can use the Anderson port of the RV output cable to power the RV. RV cable purchase link

Runtime = Capacity × DoD × η ÷ (load power+self-consumption power)
Note:
1. DoD refers to the Depth of Discharge, η is the local inverter efficiency. DoD=90%, η=88%.
2. The above data is for reference ONLY.