AC60P

Standard
AC60P:
1. AC charging cable - L=1500mm (US, UK), L=1800mm (Japan, Europe, Australia)
2. PV charging cable - L=1500mm
3. Car charging cable - L=1500mm
B80P:
1. B80P battery cable - L=800mm
Others:
Lead-acid battery charging clip to cigarette lighter L=500mm
Cigarette lighter to DC5521 cable (12V) - L=720mm
Lead-acid battery charging cable Lead-acid battery charging clip to DC7909 L=400mm
Type-C to Type-C cable L=2000mm
B80P power bank mode output cable L=720mm

Can be used alone, AC60P has a battery pack inside

AC60P can only be connected to B80P, and supports connecting up to two B80Ps, with a capacity of up to 2116Wh.

Connect AC60P and B80P with B80P battery cable, which is included in the B80P box.

Yes, the default standard UPS mode maintains SOC at 100% all the time, mainly used as a backup system.

Within 20ms.

Support simultaneous charging and discharging.

Yes, the AC60P is IP65 rated and can protect against low pressure water jets from any direction when the dust plug is in place.

It cannot be used in the rain. IPX5 only means that the product has obtained the protection level certification for protecting against low-pressure water jets. It does not mean that the product is completely waterproof and can be used in the rain.

Only supports Bluetooth connection APP.

You can use the AC60P to charge your devices in cold weather, but please avoid recharging it below freezing. The operating temperature for AC60P is:
Charging: 0℃~40℃ / 32℉~104℉
Discharging: -20~40℃ / -4~104℉

1. When the SOC drops to 5%, charge the product immediately.
2. Before storing the product, charge it to 60% SOC to maintain optimal condition. In addition, power off the device and disconnect all electrical connections.
3. Store the product in a cool and dry place, away from flammable or combustible materials and gases.
4. The power station can be safely stored in a temperature range of -20°C to 45°C (-4°F to 113°F). However, if stored for more than one month, it is recommended to keep the ideal storage temperature around 30°C (86°F).
5. Fully cycle the product every 3 months to maintain the health of the battery.

1. The output specifications, voltage and frequency of the generator need to be within the input range of the adapter. If they are unstable, you can turn on the grid adaptive mode in the APP for adaptation.
2. Does the maximum output power of the generator meet the maximum AC input power of our machine? If not, our machine can adjust the charging mode to reduce the maximum AC input power.
3. The output of the generator is a sine wave.

AC60P can connect 1*PV120 or 1*PV200.

Yes, the solar panels must meet the following conditions:
1) Total VOC:12V~28V
2) Total power: 200W max
3) With MC4 connectors
4) Is there a micro inverter? The micro-inverter cannot charge the AC60P directly. The AC60P can be charged by the micro-inverter through the AC wall charger.
Note: When the VOC exceeds 28V, you can purchase a third-party 24V DC/DC charger to reduce the voltage to achieve solar charging.

The AC180P supports AC+DC dual charging, but the DC has only one input port, so it only supports AC+ solar panel charging or AC+ car charging at the same time

AC/AC+PV maximum charging power:
1. Standard mode 250W
2. Silent mode 160W
3. Fast charging mode 600W
PV maximum charging power;
1. Standard mode, fast charging mode 200W
2. Silent mode 160W
Note: When AC+PV input, PV input will be prioritized

Charging time (estimated) = (Capacity/Charging power) + Trickle charging time
Trickle charging time for Bluetti power station is typically 0.5~1 hours

The battery pack can be connected to PV or adapter to charge the entire system.

Runtime = Capacity × DoD × η ÷ (load power+self-consumption power)
Note:
1) DoD refers to the Depth of Discharge, η is the local inverter efficiency. DoD=90%, η=85%.
2) The above data is for reference ONLY.

Yes
1. If the customer's lead-acid battery is equipped with an AC-DC adapter, charge the battery from the machine's AC output port
2. You can also charge the battery directly from the machine's DC 12V output port, cable purchase link

Support simultaneous charging and discharging.

AC60P supports AC+DC dual charging, but DC has only one input port, so it only supports AC+solar panel charging or AC+car charging at the same time.

Yes, when charging AC60P via 12V/24V DC/DC charger/MPPT controller/solar controller, it is recommended to use 24V because the charging power is higher.

Yes, the maximum output voltage of B80P power bank mode is 26V, which supports charging devices such as EB3A, EB55, EB70, AC2P, AC180P, etc.
Press and hold the power button of the battery pack for 5~10 seconds until the power button flashes

Yes
1. If the lead-acid battery is equipped with an AC-DC adapter, the battery can be charged from the machine's AC outlet
2. The battery can also be charged directly from the machine's DC 12V outlet

Power saving mode. When this function is turned on, if the AC or DC of the machine has no equipment or the load power is too small, the machine will automatically turn off the AC or DC after a period of time to reduce the machine's self-consumption and save power. The specific power and time can be set in the APP.

AC60P can carry up to 1200W pure resistive load when turned on in Hercules mode, but two conditions must be met:
1. The load must be a pure resistive load;
2. It must be used off-grid.

When the weak power grid/generator at the customer's home charges our machine, the AC output voltage or frequency of the weak power grid/generator is unstable and cannot stably charge our machine. In this case, we can turn on the grid adaptive mode to adapt to the customer's power grid/generator.

Yes, as long as the total load power does not exceed the maximum output power of the machine.