AC200P L

The rated AC output power is 2400W, and the maximum output power is 2500W when AC+DC is off-grid

Support simultaneous charging and discharging

Runtime = Capacity × DoD × η ÷ (load power+self-consumption power)
Note:
1. DoD refers to the Depth of Discharge, η is the local inverter efficiency. DoD=95%, η=93%.
2. The above data is for reference ONLY.

1.AC200PL can be connected to 1-5*PV120, 1-5*PV200, 1-3*PV350, 1-3*PV420
2. It is best to connect all solar panels in series, because the AC200PL PV input is a wide voltage range of 12V~145V, and the maximum input current is only 15A, the series voltage increases, and the current increases, so the series efficiency is higher, pay attention to not mixing different types of solar panels, otherwise it will affect the efficiency. Long time will damage the solar panels
3. Solar input current can exceed 15A, our machine will limit the current, but beyond that is equivalent to a waste, the current can exceed, the voltage can not exceed
4. Solar input power can exceed 1200 watts, as long as the total PV VOC does not exceed 145V

Yes, as long as the solar panel specifications are within the following range:
1. Total VOC: 12V~145V
2. Total power: maximum 1200W
3. With MC4 connector

Yes, but please note that your solar roof must meet the following conditions:
1. Total VOC 12V~145V
2. Connect the MC4 connector
3. Whether there is a micro inverter, micro-inverter can not directly charge AC200PL, AC200PL can only be micro-reverse charge through AC wall charging

1. Can be used alone, AC200PL internal battery pack
2. No,AC200PL is only compatible with B210P,B230,B300
3. P090D is used to connect AC200PL to B230 or B300, and P090D is included in the battery pack case. The AC200PL is connected to B210P by B210P battery line M28 to P090D, which needs to be purchased separately.

1. The AC200PL supports a maximum of 2 battery packs, and the AC200PL is connected to a B230, with a capacity of up to 4352Wh; AC200PL is connected to 2 B300s with a capacity of up to 8448Wh; The AC200PL is connected to 2 B210Ps with a capacity of up to 6604Wh
2. Do not connect expansion battery packs of different models to the AC200PL

Separate battery packs can be connected to PV or adapters to charge the entire system, but the AC200PL does not show the charging power of separate battery packs

The main differences are as follows:
1. UPS: AC200PL has it, AC200MAX does not
2. Maximum output power: AC output power of AC200PL is 2400W; The AC200MAX has an AC output power of 2200W
3. DC output, the RV port of AC200PL needs to output 12/20A through D40; The RV port of the AC200MAX outputs 12V/30A; The AC200PL does not have wireless charging, while the AC200MAX has wireless charging
4. AC charging power: The AC200PL has a maximum AC charging power of 2400W;while the AC200MAX needs to be charged via an AC adapter and has a maximum power of 500W
5. PV charging power: The AC200PL's PV charging power is 1200W, while the AC200MAX's PV charging power is 900W
6. APP function: AC200MAX only supports Bluetooth connection, while AC200PL supports Bluetooth and WiFi connection
7. Battery capacity: AC200PL capacity 2304Wh, AC200MAX capacity 2048Wh

The main differences are as follows:
1. Protection level: AC240P is IP65, while AC200PL is IP20
2. Battery capacity: AC200PL itself capacity 2304Wh, and support with B210P/B230/B300 expansion, capacity up to 8448Wh, and AC240P itself capacity 1843Wh, support with 4 B210P expansion, capacity up to 10443Wh
3.12V/30A RV port: AC200PL RV port needs to output 12/20A through D40; The RV port of the AC240P outputs 12V/30A
4. PV input range; The PV input range of AC240P is 11V~60V, 21A; The PV input range of AC200PL is 12V~145V, 15A
5. AC240P supports parallel, while AC200PL does not support parallel

1.The 48V/8A RV port of 1AC200PL requires a D40 for output,D40 Purchase link
2. Can not DIY RV line for output

Power saving mode: After the function is turned on, the machine AC or DC does not carry the device or the load power is too small, the machine will automatically turn off the AC or DC after a period of time, in order to reduce the power consumption of the machine and save power, the specific power and time can be set in the APP

The AC200PL can carry pure resistive loads up to 3600W/3000W (day scale) when turned on in Hercules mode, subject to two conditions
1. The load must be pure resistive load
2. Off-grid use

When the weak power grid/generator of the customer's home charges our machine, because the AC output voltage or frequency of the weak power grid/generator is unstable, it is not possible to stably charge our machine, then the grid adaptive mode can be turned on to adapt to the customer's grid/generator

The machine will automatically switch the DC input source to "PV" or "Others" by detecting the DC input source itself.

I do. It supports 4 UPS modes:
1. Standard UPS mode - (By default, SOC is maintained at 100% all the time, mainly used for backup system)
2. Time control UPS mode - (recommended for power grid peak-valley difference area)
3. Pv priority UPS mode - (recommended for areas with sufficient PV)
4. Custom UPS mode - (Combine the above three modes for customers to choose freely)

Within 20ms.

No, please put it in a dry place, AC200PL operating humidity range of 10%~90%

You can use the AC200PL to charge your devices in cold weather, but please avoid recharging it below freezing. The operating temperature for AC200PL is:
Charging: 0℃~40℃ / 32℉~104℉
Discharging: -20~40℃ / -4~104℉

Bluetooth and WiFi connection apps are supported

1. The output specifications, voltage and frequency of the generator need to be within the input range of the adapter. If it is unstable, you can open the grid adaptive mode in the APP for adaptation
2. Whether the maximum output power of the generator meets the maximum AC input power of our machine, if not, our machine can lower the maximum AC input current to reduce the maximum AC input power
3. The output of the generator is sine wave

cannot

1. When SOC drops to 5%, charge the product immediately.
2. Before storing the product, please charge it to 60% SOC to maintain the best condition. In addition, turn off the power to the device and disconnect all electrical connections.
3. Store the product in a cool, dry place away from flammable or combustible materials and gases.
4. The plant can be safely stored in a temperature range of -20°C to 45°C (-4°F to 113°F). However, if the storage time is longer than one month, it is recommended to keep the ideal storage temperature around 30°C (86°F).
5. Complete the cycle of the product every 3 months to maintain the health of the battery.

AC+DC dual charge is supported, but DC has only one input port, so it only supports AC+ solar panel charging or AC+ car charging at the same time

may
1. If the lead-acid battery is equipped with an AC-DC adapter, the battery can be charged from the machine AC output outlet
2. You can also charge the battery directly from the DC 12V output outlet of the machine, and the connection line is purchased

Charging time (estimated) = (Capacity/Charging power) + Trickle charging time
Trickle charging time for Bluetti power station is typically 0.5~1 hours

cannot

1. The 48V/8A RV port of the AC200PL requires a D40 for output
2. Can not DIY RV line for output

We need to power the RV load with the D40

Standard configuration:
AC200PL
1. Us 15A AC charging cable -L=1800mm, European 16A/ UK 13A/ Australian 10A AC charging cable -L=1500mm
2.PV charging cable -L=700mm
3. Car charging cable -L=500mm
4.DC input cable -L=1000mm
other
20A AC Charging cable -L=1800mm (Low voltage only)
Lead-acid battery charging clip L=500mm
48VRV cable (for D40) L=1000mm
Cigarette lighter to DC5521 line -L=720mm
Type-C to Type-C wire L=2000mm
P150D to P090D Battery cable -L=800mm
B210P battery cable M28 to P090D battery cable -L=800mm

Do not. Long-term placement may loosen the internal structure. Upright placement is recommended.

Not recommended, because the wind turbine due to the unstable air volume, the wind turbine output voltage and frequency will be unstable, can not be stabilized in the range of our machine input, directly to our machine charging may be intermittent, or even unable to charge

Yes. However, the max charging power would be limited to 100W / 200W. And please setup the "DC input source" to "Others".

Yes, as long as the total load power does not exceed the maximum output power of the machine

No, the maximum AC output power of AC200PL is 2400W, and the maximum output can only be 20A when the output is 120V, which is the maximum support for 30A of the TT-30 socket, but it does not mean that the machine will output 30A, the TT-30 output outlet is mainly to provide customers with more socket choices