EB3A

AC maximum charging power:
1. Standard mode 268W
2. Silent mode 100W
3. Fast charging mode 300W (low voltage)/340W (high voltage)

PV maximum charging power;
1. Standard mode, fast charging mode 200W
2. Silent mode 100W

AC+PV maximum charging power;
1. Standard mode 268W
2. Silent mode 100W
3. Fast charging mode 430W
Note: When AC+PV input, PV input will be prioritized

Standard cables:
1.AC charging cable - L = 1800mm/1500mm (UK standard)
2. PV charging cable - L = 1500mm
Optional cables:
Car charging cable, L = 720mm
Type-C to Type-C cable L = 1500mm

Yes, the default standard UPS mode maintains SOC at 100% all the time, mainly used as a backup system.

Within 20ms.

No, please put it in a dry place. The operating humidity range of EB3A is 10%~90%.

Charging time (estimated) = (Capacity/Charging power) + Trickle charging time.
Trickle charging time for Bluetti power station is typically 0.5~1 hours.

Support simultaneous charging and discharging.

EB3A supports AC+DC dual charging, but DC has only one input port, so it only supports AC+solar panel charging or AC+car charging at the same time.

You can use the EB3A to charge your devices in cold weather, but please avoid recharging it below freezing. The operating temperature for EB3A is:
Charging: 0℃~40℃ / 32℉~104℉
Discharging: -20~40℃ / -4~104℉

Runtime = Capacity × DoD × η ÷ (load power+self-consumption power)
Note:
1. DoD refers to the Depth of Discharge, η is the local inverter efficiency. DoD=90%, η=90%.
2. The above data is for reference ONLY.

EB3A can carry up to 1200W pure resistive load after turning on the Hercules mode, but two conditions must be met:
1. The load must be a pure resistive load;
2. It must be used off-grid.

Power saving mode. When this function is turned on, if the AC or DC of the machine has no equipment or the load power is too small, the machine will automatically turn off the AC or DC after a period of time to reduce the machine's self-consumption and save power. The specific time can be set in the APP.

1. The output specifications, voltage and frequency of the generator must be within the input range of our machine.
2. The maximum output power of the generator meets the maximum AC input power of the machine.
3. The output of the generator is a sine wave.

EB3A can connect to one PV120 or one PV200.

1. The solar input current can exceed 8.2A. Our machine will limit the current. Exceeding it is equivalent to waste. The current can exceed, but the voltage cannot exceed.
2. The solar input power can exceed 200 watts, as long as the total PV VOC does not exceed 28V.

Yes, the solar panels must meet the following conditions:
1. Total VOC:12V~28V
2. Total power: 200W max
3. With MC4 connectors
4. Is there a micro inverter? The micro-inverter cannot charge the EB3A directly. The EB3A can only be charged by the micro-inverter through AC wall charging.
Note: When the VOC exceeds 28V, you can purchase a third-party 24V DC/DC charger to reduce the voltage to achieve solar charging.

It is not recommended. Because the wind volume of the wind turbine is unstable, the output voltage and frequency of the wind turbine will be unstable and cannot be stable within the input range of our machine. Directly charging our machine may be intermittent or even unable to charge.

Yes, you can purchase the cable.

Yes.
1. If the lead-acid battery is equipped with an AC-DC adapter, the battery can be charged from the AC output port of the machine
2. The battery can also be charged directly from the DC 12V output port of the machine. The link to purchase the connecting cable.

Yes, when charging EB3A via 12V/24V DC/DC charger/MPPT controller/solar controller, it is recommended to use 24V because the charging power is higher.

Yes. Can only be connected to the Bluetti App via Bluetooth.

No, please keep it in a dry place.

1. When the SOC drops to 5%, charge the product immediately.
2. Before storing the product, charge it to 60% SOC to maintain optimal condition. In addition, power off the device and disconnect all electrical connections.
3. Store the product in a cool and dry place, away from flammable or combustible materials and gases.
4. The power station can be safely stored in a temperature range of -20°C to 45°C (-4°F to 113°F). However, if stored for more than one month, it is recommended to keep the ideal storage temperature around 30°C (86°F).
5. Fully cycle the product every 3 months to maintain the health of the battery.

EB3A does not have a capacity expansion function. You can only charge EB3A in battery pack power bank mode for false capacity expansion, and it only supports false capacity expansion with B80P. Cable purchase link.

Not recommended, as long-term placement may cause the internal structure to loosen. It is recommended to place it upright.

No, you have to use T200S to charge EB3A. The DC input voltage range of EB3A is 12V~28V, while the maximum output voltage of T500 is 58.8V, which exceeds the DC input voltage range of EB3A. Using T500 to charge will burn out EB3A.

Yes, as long as the total load power does not exceed the maximum output power of the machine.